Skip links

Archive

Kickerless Construction

Kickerless construction for positioning vertical formwork off a slab has the following advantages over the construction of a traditional kicker against which the vertical forms are clamped:

jonnyhough

jonnyhough

Joints in external paving

Tensile and compressive stresses will be induced in concrete by restrained thermal and moisture-related contraction and expansion effects. Thermal changes can result from the heat of hydration of the concrete or from exposure to the environment. Changes in moisture content of the concrete may result in shrinkage or expansion, but shrinkage is predominant. Joints are provided in pavements to reduce the stresses generated by thermal and moisture changes and to allow horizontal movement. As the heat of hydration movements occur in the first few days after construction, joints need to be provided at an early stage – usually within 24 hours of casting.

jonnyhough

jonnyhough

Bridge expansion joints

Bridges expand and contract due to temperature changes. In larger structures expansion joints are required to accommodate the resulting movements between adjacent bridge deck spans or between the bridge deck and abutment. The joint must provide a suitable running surface for traffic crossing the expansion gap. Various types of joint are defined in the National Highways CD357, Bridge

jonnyhough

jonnyhough

Adhesive connections between precast units

Connections between precast concrete units can be formed using adhesives (such as epoxies) rather than cement-based mortars. The adhesives are significantly stronger that the surface layer of the concrete, which must be suitably prepared to remove loose material such as laitance. Adhesive joints should be designed so that they act primarily in shear or compression. The major advantage of adhesives is their rapid gain in strength. Suitably formulated epoxy adhesives gain their full strength in a matter of hours while cementitious materials will take several days or weeks.

jonnyhough

jonnyhough

Construction Joints – horizontal

It is often not possible to complete a job at one go, for example because of the size or complexity of the structure or because of limited materials or manpower. When work resumes it will be necessary to place fresh concrete on or against the previous pour, that will have already hardened. The resultant contact surface is known as a construction joint or daywork joint. Such joints must be formed carefully so that they transmit the required forces and, where appropriate, do not leak. Firstly the surface of the hardened concrete must be clean and free from laitance (the relatively soft surface layer) and any dust or debris. Then the fresh concrete must be place and compacted so that it bonds properly to the surface of the previously place concrete.

jonnyhough

jonnyhough

Construction joints – vertical

It is often not possible to complete a job at one go, for example because of the size or complexity of the structure or because of limited materials or manpower. When work resumes it will be necessary to place fresh concrete on or against the previous pour, that will have already hardened. The resultant contact surface is known as a construction joint or daywork joint. Such joints must be formed carefully so that they transmit the required forces and, where appropriate, do not leak. Firstly the surface of the hardened concrete must be clean and free from laitance (the relatively soft surface layer) and any dust or debris. If it is too hard, hand-held tools or abrasive blasting will be necessary. (Note that the use of hand-held tools should be limited for Health and Safety reasons.) Care must be taken to avoid dislodging aggregate. Then the fresh concrete must be place and compacted so that it bonds properly to the surface of the previously place concrete.

jonnyhough

jonnyhough

In-situ to precast connections

There are many situations in which a connection is required between a precast concrete element and in situ concrete. A typical example is the connection between precast concrete bridge beams and the in situ concrete deck slab (see also Civil engineering/bridges/precast bridge beams). So that the precast and in situ concretes act compositely, it is necessary to ensure an adequate transfer of load (mainly in shear) between the two. This is achieved by the surface of the precast concrete being roughened (generally as one stage of the production process) and having some reinforcing steel projecting through the interface. (The latter prevents separation of the surfaces as well as carrying some of the shear load.) Guidance on the surface preparation and the amount of reinforcement required for a particular application is given in the appropriate design standards.

jonnyhough

jonnyhough

Precast to precast connections

The joints between precast units are required to transmit loads. In simple cases, such as a floor slab resting on a beam, this will be chiefly in compression though in other situations there will be a requirement to transmit shear loads. In both cases the basic principle is that there should be sufficient overlap between the two units so that the bearing or shear stresses are sufficiently low. Packing pieces (e.g. steel shims) may be required to obtain the required levels for the units.

jonnyhough

jonnyhough

Bridge cantilever construction – precast

Balanced cantilever construction is an economical method when access from below is expensive or practically impossible. The cross-section is normally a box. Segments may be cast in-situ or precast. Construction starts from the top of a pier, with the segment normally fixed to the pier either permanently or temporarily during the construction. (Construction can be carried out from an abutment provided there is a balancing weight to counteract the segments in the span).

jonnyhough

jonnyhough

The Concrete Society

The Concrete Society is an independent membership organisation that exists to promote knowledge and support the advancement of concrete.

Quick Links
Policies
Contact Us
This website uses cookies to improve your web experience.